PERRIN 2015+ Subaru WRX Blow Off Valve Kit Recirculation Only - PSP-TAC-615RD
Have questions?
-
Guaranteed Quality
Best Parts Every Time
-
Expert Help
Build Advisors Are Standing By
-
Secure Shopping
SSL Verified
-
Worldwide Delivery
Free shipping on most orders over $249 in US 48
Perrin Performance
PERRIN 2015+ Subaru WRX Blow Off Valve Kit Recirculation Only - PSP-TAC-615RD
- SKU:
- ds_GSWC_PSP-TAC-615RD
- UPC:
- PSP-TAC-615RD
- MPN:
- PSP-TAC-615RD
- LTL:
- N
- CARB:
- This product is not CARB Legal and not for sale in California
- Exclude-States:
- CA
PERRIN 2015+ Subaru WRX Blow Off Valve Kit Recirculation Only - PSP-TAC-615RD
Overview
Add horsepower, quicker response, and reliability with the PERRIN BOV/BPV. A must-have replacement for the leaky, slow responding, and plastic OEM blow off valve.
No Tuning Required
Increase horsepower and torque without ECU recalibration or tune! This part is designed and tested to work safely on your vehicle without any tuning required! However, more power can be gained with proper ECU tuning! Confirm any tune or recalibration you add is specific for ALL modifications added to the vehicle.
Essential For Proper Performance
During testing, it was determined that until approximately 3 psi of boost is reached, the OEM blow off valve does not seal. This leads to a loss in horsepower and slower response from your turbo. The PERRIN BPV solves this problem with a proper seal as well as being fully adjustable. This means faster response times, consistent boost, and overall better drivability.
High Flow
The tiny outlet on the OEM BOV restricts the rate ar which boost can be vented. Cars running higher boost levels and larger turbos can experience compressor surge, damaging your turbo. The PERRIN BPV has a much larger outlet and is fully adjustable, eliminating this concern. With large inlets and outlets, the PERRIN BPV is sized perfectly to relieve any amount of boost pressure without fear of compressor surge. Don't be fooled by giant oversized blow-off valves, these inlet and outlet sizes were chosen to ensure the perfect balance of flow and to maintain boost in your system, without ruining response by dumping too much boost.
Adjustable Relief Pressure
The PERRIN BPV cap features adjustable spring tension, which allows for an adjustment when the blow-off valve vents. A looser setting will make it act smooth and more like stock. Setting it harder will cause it to vent later and with significantly increased boost levels. This adjustment is important in maintaining the air within the boost system without reducing turbo response.
Adjustable Flow Control
The unique design allows you to control the volume of air released when the blow-off valve vents. Adjusting the volume of air helps maintain the perfect amount of boost in your system during shifts without causing compressor surges. Venting too little can damage the turbo, venting too much air can make the throttle less responsive. This adjustment is independent of the relief pressure allowing for a totally customizable bypass valve,
Recirculation Is Job #1
It is vital that a bypass valve for your WRX recirculates the air back to the intake track to maintain proper air-fuel ratio and driveability between shifts. While this can be set up as a vent-to-atmosphere style blow-off valve, we only recomment that on cars running aftermarket Speed Density type tuning (cars without mass airflow sensor).
Low Maintenance
The PERRIN BPV requires very little maintenance but when needed, it's very easy and quick to disassemble. Two O-rings are used to seal vital components from the elements making for extended time between service intervals. There are no special tools required and maintenance can be performed without removing the blow-off valve from the vehicle.
Direct Fit & Pre-Set Adjustment
Included with every PERRIN BPV are the necessary components to make this a direct bolt-on for your WRX. Each bypass valve is pre-set out of the box to work perfectly with every application, so no adjustment is required.
Construction
The PERRIN BPV cap, piston & flange are all CNC machined from 6061 Billet Aluminum. The body is CNC machined from a single block of aluminum. This makes for a clean look that reduces potential failure points and leaks without additional perts.
Finish
The PERRIN BPV body comes with a red anodized finish and the cap is black anodized. The anodizing keeps the bypass valve looking great during its lifespan. The bypass valve body and cap are laser engraved in vibrant lettering to make it easier to read.
Related Products
IAG Performance
IAG Blow Off Valve Recirculation Block Off Plug For 2015-21 Subaru WRX
Availability: Usually Ships in 24 to 72 Hours