{"product_id":"radium-engineering-catch-can-kit-for-2022-subaru-wrx-pcv-fluid-lock-20-0754-fl","title":"Radium Engineering Catch Can Kit For 2022+ Subaru WRX - PCV Fluid Lock - 20-0754-FL","description":"\u003ch2 style=\"text-align:center;\"\u003eCATCH CAN KITS, 2022+ SUBARU WRX\u003c\/h2\u003e\u003chr style=\"border:none;border-top:1px solid #e0e0e0;margin:24px 0;\"\u003e\u003cdiv class=\"video-embed\" style=\"position:relative;width:100%;padding-bottom:56.25%;height:0;overflow:hidden;\"\u003e\u003ciframe src=\"https:\/\/www.youtube.com\/embed\/Kb440MG_ROY?start=0\u0026amp;end=0\u0026amp;autoplay=0\u0026amp;loop=0\u0026amp;rel=1\" allowfullscreen loading=\"lazy\" style=\"position:absolute;top:0;left:0;width:100%;height:100%;border:0;\"\u003e\u003c\/iframe\u003e\u003c\/div\u003e\u003ch2 style=\"text-align:center;\"\u003eOVERVIEW\u003c\/h2\u003e\u003cp\u003eThe PCV catch can kit runs inline between the PCV valve and the intake manifold and promotes clean filtered air back into the engine. When the intake manifold pressure is close to or greater than atmospheric pressure, the PCV valve closes, and this hoses experience no flow. The PCV hoses will experience metered vacuum when the engine is idling, steady state cruising, and decelerating. This would normally draw unwanted crankcase vapor, unspent fuel, and oil sludge into the intake manifold immediately after a high load run. \u003cbr\u003e\u003cbr\u003eThe catch can draws out oil and water condensation from the crankcase gasses that would otherwise be drawn into the intake manifold. This prevents oil buildup in the intake, intercooler system walls, throttle body, and intake manifold. This effectively raises the octane, can increase engine performance from cleaner inlet air, and can lower hydrocarbon emissions. The closed system prevents unwanted oil vapors from entering into the cabin. Catch can kits include everything needed for a complete installation.\u003c\/p\u003e\u003ch2 style=\"text-align:center;\"\u003eFLUID LOCK® CATCH CANS\u003c\/h2\u003e\u003cp\u003eIn 2022, Radium Engineering implemented a revolutionary design change to the 7 fluid ounce standard catch can. An inherent problem always existed with typical catch cans when not serviced regularly. The fluid contaminants will eventually leave the reservoir pouring into the air intake system causing poor engine performance. To resolve this issue, Radium created the Fluid Lock® Catch Can. This contains a patented mechanism that prevents the reservoir from overfilling and traps the collected fluids until it is emptied.\u003c\/p\u003e\u003ch2 style=\"text-align:center;\"\u003eCOLLECTION \u0026amp; EMPTYING\u003c\/h2\u003e\u003cp\u003eThe rate that your catch cans will collect oil and moisture contaminants will vary from one individual vehicle to the next, so there is no set emptying interval. PCV catch cans tend to collect more than CCV catch cans. You should check the level of your catch can using the integrated dipstick starting at 3-4 weeks of driving and repeat as needed to determine how often they should be emptied based on what you see.\u003cbr\u003e\u003cbr\u003eCatch cans can be emptied by unscrewing the lower reservoir and removing it from the vehicle to dump out, or in cases where there is available space under the catch can, the Petcock Drain Kit can be installed and used to drain them.\u003cbr\u003e\u003cbr\u003eIn cases where oil collection is excessive you may have to address an issue with the engine. The reasons a catch can will collect an excess of oil include\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eExcessive blowby from engine damage\u003c\/li\u003e\n\u003cli\u003eCrankcase windage from an over-full oil level\u003c\/li\u003e\n\u003cli\u003ePoor placement of breather ports and\/or poor baffling inside breather ports\u003c\/li\u003e\n\u003cli\u003ePCV valve not closing and leaking under heavy load\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2 style=\"text-align:center;\"\u003eNOTES:\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eThe catch can mounts to threaded bosses on the ABS unit.\u003c\/li\u003e\n\u003cli\u003eThe PCV catch can kit is compatible and recommended to be used with the CCV catch can kit.\u003c\/li\u003e\n\u003cli\u003eNo extra inline check valve is required since Radium catch cans are pressure sealed.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Radium Engineering","offers":[{"title":"Default Title","offer_id":48062465016026,"sku":"RAD20-0754-FL","price":227.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0828\/8623\/0234\/files\/cf9219b14f081f2963ab1460b487a663__21721.1658493092.1280.1280.jpg?v=1781530222","url":"https:\/\/www.iagperformance.com\/products\/radium-engineering-catch-can-kit-for-2022-subaru-wrx-pcv-fluid-lock-20-0754-fl","provider":"IAG Performance","version":"1.0","type":"link"}